How to make floor non slippery
Do you want to know how to make a non-slip floor in your home? Find out how in this guide! We will give you all the valuable information, advice and ideas you will need to make a non-slip floor in your home.
1. How to make ceramic floor non-slip
The floors made with ceramic tiles are gorgeous and functional: easy to clean and very resistant; they are the ideal covering for the floor and walls of bathrooms and kitchens. Once wet, however, ceramic tiles become very slippery. To avoid the possibility of accidental falls, you could treat the floor’s surface with various techniques to make the ceramic floor in your home less slippery.
One of the possible treatments is applying specific products to make ceramic tiles, majolica and even porcelain stoneware rougher: these are acid-based products which chemically modify the tiles’ surfaces, making them more porous and rough and less slippery.
Since these are very aggressive chemical compounds, they need to be applied with the timing specific to each product. Excessively prolonged action of acids could damage the floor tiles and take away too much shine from the surface of the ceramic or porcelain stoneware covering.
To avoid this, after leaving the anti-slip products to act for the necessary time, specific products are used that can neutralize acids and stop the corrosion process of the surfaces. This is the best solution on how to make floor non slippery.
2. How to make marble floor non-slip - How to make floor non slippery
Marble is one of the most elegant and classy floor coverings and also has excellent waterproofing qualities that make it the ideal material for bathroom and kitchen floors. To avoid slipping on the marble floor, exceptionally if wet, you can use the marble slabs worked with special techniques that give the marble greater roughness and less slipperiness, such as bush hammering and sandblasting. , flaming or scratching.
However, suppose you already have a marble floor in your home and still want to reduce its slipperiness. You can always polish it with special non-slip waxes, which leave a thin layer of material with a high gripping power on the floor covering, and therefore not slippery, even if giving the marble its characteristic lustre and brilliance.
Before you can apply the special non-slip waxes, you will need to thoroughly clean your floor to remove all traces of previous waxing. You can do this with a thorough wash, using a solution of ammonia and water, which you can spread with a microfiber cloth, and with a second wash based on water and bicarbonate, Marseille soap flakes and a little alcohol.
3. Coating with non-slip paints - How to make floor non slippery
Another system used to make ceramic floors non-slip consists of applying a thin layer of polyurethane paint over the tile covering of the floor. Polyurethane paints with high resistance to abrasion, atmospheric agents and ultraviolet rays are generally used, and which can accentuate the decorations of floor coverings of all kinds, from terracotta to porcelain stoneware and natural stone.
The surfaces to be treated must be cleaned using a product with a high degreasing power to allow the paint to adhere correctly. The drying time is around 45 minutes to two hours, depending on the type of coatings on which they are applied. At the end of the treatment, it is necessary to remove the paint residues with adequate cleaning and to evaluate if the result obtained is in line with one’s expectations regarding slipperiness and gloss of the floor, and if necessary, repeat the treatment.
4. Coating with non-slip strips - How to make floor non slippery
If you need to make floors with small surfaces non-slip and perhaps even uncomfortable to treat, you can also opt for applying strips of non-slip material. They are ideal for making steps and ramps of stairs non-slip, where greater adherence to foot traffic is also required due to the greater danger of any falls while climbing or descending stairs.
Depending on the coating of the steps, strips of non-slip materials with different finishes and colors can be applied: there are strips with marble, wood or ceramic effect, which can go almost unnoticed without standing out too much on the steps while ensuring excellent adhesion to the tread.
The application of the anti-slip strips is quite simple. After thoroughly cleaning the surfaces of the steps to ensure maximum adhesion of the glues of the strips, apply them by removing the protective strip of the self-adhesive strips and placing them on the steps. However, if you want to ensure that the non-slip strips last longer, you can add tights to the steps before applying the strips.
How to make floor non slippery. Are you still sure you want to do it by yourself?
Making a non-slip floor treatment is not too easy and requires some experience to be done correctly. If you don’t want to try your hand at a job of this kind, because maybe you think you don’t know enough about how to make a non-slip floor, you can always contact a professional who takes care of making the floors in your home slip; contact us for a quotation and free demonstration on your floor.
